# Camera not detected Capture Card is on

**URL:** <https://community.stereolabs.com/t/camera-not-detected-capture-card-is-on/10307>\
**Category:** ZED X\
**Created:** [November 11, 2025, 2:35pm UTC](https://community.stereolabs.com/t/camera-not-detected-capture-card-is-on/10307 "2025-11-11T14:35:12Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![tillwald](https://community.stereolabs.com/letter_avatar_proxy/v4/letter/t/b2d939/32.png) [@tillwald](https://community.stereolabs.com/u/tillwald)\
**Post date:** [November 11, 2025, 2:35pm UTC](https://community.stereolabs.com/t/camera-not-detected-capture-card-is-on/10307/1 "2025-11-11T14:35:12Z")

</div>

I am running a Jetson Orin AGX connected to a [Stereolabs](https://www.stereolabs.com/) ZED Link Capture Card Quad. I have four ZedXOne GMSL cameras connected to this setup.

The problem is that the cameras are not being detected. Running the command `ZED_Explorer -a` lists no cameras. Crucially, the cameras are also not generating any heat, which strongly suggests a lack of power delivery.

**Debugging Step:** I measured the current draw and found that the capture card (with 4 dummy cameras connected) is only pulling 1.4 mA at 24V in its idle state. This is significantly low. I suspect a power issue with the card itself or the GMSL power distribution system.

**Setup Context:**

- **System Status:** This is a existing setup. It has previously worked correctly.

Could you please advise on what steps I should take to isolate this suspected power issue on the capture card?

Thank you, and looking forward to your fast support!

---

<div class="post-metadata">

**Author:** ![Myzhar](https://community.stereolabs.com/user_avatar/community.stereolabs.com/myzhar/32/11_2.png) [@Myzhar](https://community.stereolabs.com/u/Myzhar)\
**Post date:** [November 11, 2025, 3:08pm UTC](https://community.stereolabs.com/t/camera-not-detected-capture-card-is-on/10307/2 "2025-11-11T15:08:57Z")

</div>

Hi @tillwald

To assist you better, we need additional information regarding your device’s condition and system setup.

Please open a terminal console (`Ctrl+Alt+t`) and run these commands:

- `sudo ZED_Diagnostic --dmesg`
- `sudo ZED_Diagnostic -c`

After executing the commands, kindly send me the files `dmesg.log` and `ZED_Diagnostic_Results.json` located in the folder where the commands were run.

---

<div class="post-metadata">

**Author:** ![tillwald](https://community.stereolabs.com/letter_avatar_proxy/v4/letter/t/b2d939/32.png) [@tillwald](https://community.stereolabs.com/u/tillwald)\
**Post date:** [November 11, 2025, 3:38pm UTC](https://community.stereolabs.com/t/camera-not-detected-capture-card-is-on/10307/3 "2025-11-11T15:38:38Z")

</div>

dmesg.log: [https://drive.google.com/file/d/1l0Kz9DC3Gd3IzNv4bX\_oaFd\_\_VqIXjQb/view?usp=drive\_link](https://drive.google.com/file/d/1l0Kz9DC3Gd3IzNv4bX_oaFd__VqIXjQb/view?usp=drive_link)

ZED\_Diagnostic: [https://drive.google.com/file/d/10RCNsI0BzB-U7Lig-y7fnFHM-qtCePDJ/view?usp=drive\_link](https://drive.google.com/file/d/10RCNsI0BzB-U7Lig-y7fnFHM-qtCePDJ/view?usp=drive_link)

---

<div class="post-metadata">

**Author:** ![Myzhar](https://community.stereolabs.com/user_avatar/community.stereolabs.com/myzhar/32/11_2.png) [@Myzhar](https://community.stereolabs.com/u/Myzhar)\
**Post date:** [November 14, 2025, 5:03pm UTC](https://community.stereolabs.com/t/camera-not-detected-capture-card-is-on/10307/4 "2025-11-14T17:03:13Z")

</div>

The capture card is not detected by the driver.

> [@tillwald](#):
>
> **Debugging Step:** I measured the current draw and found that the capture card (with 4 dummy cameras connected) is only pulling 1.4 mA at 24V in its idle state.

24V is out of the voltage range to power the ZED Link Quad capture card.  
The maximum power is 19V.
